How to Choose the Right Deinking Agent for Different Waste Paper Furnishes? (A Practical Guide)

Nov 11, 2026

Leave a message

April.Tian
April.Tian
April, Sales Manager of Luterra Advanced Materials. Graduated from Qilu University of Technology. Precise and friendly, she delivers professional full-cycle order service, gaining wide recognition from overseas clients.

Deinking results vary dramatically depending on the waste paper furnish. A deinking agent program that works perfectly with American old corrugated containers (AOCC) may fail with European mixed office waste or domestic recycled pulp. Choosing the right product-and adjusting the process accordingly-is the key to consistent pulp quality.

 

                              solid-deinking-agent83f59      liquid-deinking-agent91a25jpg

 

 

This guide explains how to match P-01A Solid Deinking Agent and P-01B Liquid Deinking Agent to different waste paper furnishes, and what process adjustments are needed for each.

Why Furnish Type Matters

Different waste paper grades contain different ink types, coatings, and contaminant levels:

Furnish Type Typical Ink Challenge Deinking Difficulty
AOCC (American OCC) Water-based inks, some flexo Moderate
EOCC (European OCC) Solvent-based, UV inks Moderate to high
Mixed Office Waste Toner, laser inks High
Domestic Recycled Pulp Mixed inks, high contaminant load Variable
Newsprint / Magazine Offset, flexo, some UV Moderate

The deinking agent must be selected and dosed according to the specific ink system, not just the fiber source.

Scenario 1: American Old Corrugated Containers (AOCC)

AOCC is generally the easiest furnish to deink, but it often contains flexographic water-based inks that can redeposit on fibers if not properly dispersed.

Recommended product: P-01A Solid Deinking Agent
Why: Its bio-enzyme composite activation technology and alcohol-based ink separation components are highly effective at lifting water-based inks and preventing redeposition.
Dosage: 1.0–2.0 kg per metric ton of dry pulp.
Process note: Add at the pulper inlet or before flotation. Cold water dissolution works well, saving steam.

Scenario 2: European Old Corrugated Containers (EOCC)

EOCC often contains more solvent-based inks and higher levels of stickies and coatings, which can cause deposit problems in the flotation cells and on wires.

Recommended product: P-01B Liquid Deinking Agent
Why: Its non-ionic and anionic surfactant blend disperses more evenly in the system and handles difficult inks more effectively. The liquid form allows continuous dosing via metering pump for consistent performance.
Dosage: 0.5–1.5 kg per ton of waste paper, adjusted for ink load.
Process note: Add directly to the pulper with waste paper, water, and alkali. No pre-dilution required.

Scenario 3: Mixed Office Waste (MOW)

MOW contains high levels of toner and laser-printed inks, which are notoriously difficult to deink because they are fused to the fiber surface rather than sitting on top of it.

Recommended product: P-01B Liquid Deinking Agent
Why: Liquid formulations allow easier compounding of active components and perform better on difficult-to-deink inks like toners and digital printing inks.
Dosage: 1.0–1.5 kg per ton, at the higher end of the recommended range.
Process note: Consider a two-stage approach-pulping with the deinking agent followed by dispersion or kneading to detach toner particles before flotation.

Scenario 4: Domestic Recycled Pulp with High Contaminant Load

Domestic recycled pulp often contains a mix of ink types, adhesives, and stickies. The variability makes it challenging to achieve consistent brightness and cleanliness.

Recommended product: P-01A Solid Deinking Agent
Why: Its high active content (≥99%) and broad adaptability to different ink types make it a robust choice for variable furnishes. It also reduces COD and BOD in wastewater, which is important for mills with strict discharge limits.
Dosage: 1.5–2.0 kg per ton, adjusted based on the actual ink load.
Process note: Use a combination of flotation and washing deinking. P-01A delivers both effects in one formulation.

Scenario 5: Newsprint and Magazine Waste

Newsprint and magazine waste typically contain offset and flexo inks, with some UV inks in newer publications. The fiber is shorter and more sensitive to mechanical damage.

Recommended product: P-01B Liquid Deinking Agent
Why: Its mild surfactant system is gentler on short fibers while still effectively removing ink. The liquid form allows for precise, continuous dosing to match varying ink loads.
Dosage: 0.5–1.0 kg per ton of waste paper.
Process note: Use a lower dosage and gentler pulping conditions to protect fiber strength.

 

                               solid-deinking-agent83f59       liquid-deinking-agent91a25jpg

 

Quick Selection Guide

Furnish Type Recommended Product Dosage Range Key Advantage
AOCC P-01A Solid 1.0–2.0 kg/t Cold water dissolution, dual action
EOCC P-01B Liquid 0.5–1.5 kg/t Handles difficult inks, continuous dosing
Mixed Office Waste P-01B Liquid 1.0–1.5 kg/t Better on toner and digital inks
Domestic Recycled Pulp P-01A Solid 1.5–2.0 kg/t High active content, variable furnish adaptability
Newsprint / Magazine P-01B Liquid 0.5–1.0 kg/t Gentle on short fibers

Product Specifications at a Glance

Parameter P-01A Solid P-01B Liquid
Appearance White powder Light yellow to dark brown liquid
Active content ≥ 99% ≥ 98%
pH 7–11 (1% solution) 4.0–8.0 (10% solution)
Solubility Readily soluble in cold water Fully soluble, no layering
Recommended dosage 1.0–2.0 kg/t pulp 0.5–1.5 kg/t waste paper
Shelf life 24 months 12 months

Tips for Optimizing Deinking Performance

Match the product to the ink type-water-based inks respond well to P-01A; solvent-based and UV inks need P-01B.

Adjust dosage based on ink load, not just furnish type.

Control pH-P-01A works best in alkaline conditions (pH 7–11); P-01B is more flexible (pH 4–8).

Optimize flotation and washing-both products deliver dual-action performance, but the balance can be adjusted.

Monitor wastewater load-P-01A is biodegradable and reduces COD/BOD, which matters if you have strict discharge limits.

Frequently Asked Questions

Q: Can I use one deinking agent for all furnishes?

A: It is possible, but not optimal. Different furnishes require different ink removal mechanisms. Using the right product for each furnish improves pulp quality and reduces chemical costs.

Q: How do I know which product is right for my waste paper?

A: The key factors are ink type (water-based vs. solvent-based vs. toner), contaminant level, and fiber sensitivity. P-01A is more robust for variable furnishes; P-01B is more precise for difficult inks. Free samples are available for lab testing.

Q: Can the two products be used together?

A: Yes, they can be used in combination for complex furnishes. Consult our technical team for a customized recommendation.


Ready to improve your deinking results?

Contact Luterra Advanced Materials for a free sample and expert consultation. Our technical team can help you match the right deinking agent to your specific waste paper furnish and optimize your process for maximum efficiency. [Get Free Quote / Contact Now]

Send Inquiry
Contact us if have any question

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.

Contact now!